Cannot uninstall microsoft wifi miniport adapter windows 7
- CANNOT UNINSTALL MICROSOFT WIFI MINIPORT ADAPTER WINDOWS 7 INSTALL
- CANNOT UNINSTALL MICROSOFT WIFI MINIPORT ADAPTER WINDOWS 7 DRIVER
- CANNOT UNINSTALL MICROSOFT WIFI MINIPORT ADAPTER WINDOWS 7 PATCH
- CANNOT UNINSTALL MICROSOFT WIFI MINIPORT ADAPTER WINDOWS 7 PASSWORD
- CANNOT UNINSTALL MICROSOFT WIFI MINIPORT ADAPTER WINDOWS 7 PROFESSIONAL
to protect any customer data and other sensitive data on it.Īny professional input from somebody at Microsoft to finally get a solution for this would be greatly appreciated.įirst, I apologize in advance for venting here. The device would get stolen or I would loose it somehow. The problem: Disabling "Password protection on wakeup" is not a solution at all for me personally, as I'm on the road with my notebook quite often, and I want to be sure that the data on my notebook isn't accessible without unlocking the screen, in case So, from my point of view, it seems to be something related to security (probably in conjunction with this hosted network stuff).
CANNOT UNINSTALL MICROSOFT WIFI MINIPORT ADAPTER WINDOWS 7 PASSWORD
If I change the power saving option "Password protection on wakeup" from "Require a password on (recommended)" to "Don't require a password", everything is fine concerning the time period it takes to establish the WLAN connection after wakeup (that means,Įven without the NETSH commands as described in this thread). Set to "Allowed" again - and that means, the next time my machine wakes up from sleep mode, it again takes ages (~30 - 50 seconds) before the WLAN-connections gets re-established.ĭoes anybody know how I can get the mode=disallow to be persisted?Īnother interesting fact I found before I ran over the solution using those NETSH commands: One time - as soon as I wake up my machine from sleeping after running this, the WLAN connection gets re-established quickly (less than 5 seconds) but when I check the status with "netsh wlan show hostednetwork" then, the result is that the mode is IOW, running the two commands in an elevated Command Prompt helps exactly "netsh wlan set hostednetwork mode=disallow" does not get persisted on my machine."netsh wlan stop hostednetwork" gets persisted, however,.The command "netsh wlan set hostednetwork mode=disallow" does not get persisted, so executing One time for me, that means, for one sleep-wakeup-cycle.
My problem: the solution described above in this (TechNet) thread works only The thread (my latest reply) in the Microsoft Answers forum is located Because this information is stored in HKEY_LOCAL_MACHINE, it should be sufficient to clean this up in the OS layer, and it should fix it for any other machines.I've been asked by a Support Engineer at the Microsoft Answers forum to re-create my problem here within the TechNet forum, because it is more complex than what's typically handled there.
CANNOT UNINSTALL MICROSOFT WIFI MINIPORT ADAPTER WINDOWS 7 INSTALL
Windows should now re-discover the VMXNet3 device and install it properly.
Just run DevMgmt and Show Hidden Devices, and you will automatically see the grayed-out nonpresent devices too.įor Windows 7, close any open instances of the Device Manager. Startingin Windows 8, you no longer need to start Device Manager in Nonpresent Devices mode. The following instructions apply to Windows.
CANNOT UNINSTALL MICROSOFT WIFI MINIPORT ADAPTER WINDOWS 7 PATCH
If you apply this patch in an OS layer version, you may wind up with desktops with a non-functional VMXNet3 device, and uninstalling it from the device manager does not actually remove it.
CANNOT UNINSTALL MICROSOFT WIFI MINIPORT ADAPTER WINDOWS 7 DRIVER
However, Unidesk has observed this patch to break the VMXNet3 driver when included in an OS layer update, so we do not currently recommend it. They may recommend an MS patch referenced in this VMware KB. VMware is aware of the VMXNet3 proliferation problem.
This can result in Windows not being able to bring up any network interface until the excess nonpresent device records are removed. When Unidesk is attempting to merge multiple VMXNet3 device nodes from multiple layer sources, we sometimes fail to merge them properly. So these devices accumulate in the registry as no-longer-present devices. Unlike E1000-compatible devices, which re-use the same device nodes, every new MAC address on a VMXNet3, even if it's in the same virtual PCI location, causes a new device detection. This can also happen during layer changes on a desktop.įor all versions of Unidesk & App Layering: The underlying problem is that every new instance of a VMXNet3 network device is detected by Windows as a completely separate device. Even after restarting to apply changes and rediscovering the disks, the driver does not appear to install correctly. Unidesk 2.X releases before 2.8.3: After Desktops have been backed up and restored to a new CachePoint, the NIC doesn't come up.